螺桿泵性能參數換算	The Count of Characteristic Data of Pump Selected
以下各章均列出產品性能表，當用戶根據需要在性能表中無法查得軸功率及流量時，可按如下方法近似確定：	When you can"t get the capacity power and capacity from the characteristic table you need count it：
(一)軸功率的換算	(一) The cowt of power
1. 當壓力由P變成P₁而粘度、轉速不變時，軸功率N： N = (QP₁/3.67η₀)[1+(η₀/η-1)P/P₁] (Kw) 式中: Q、P均為性能表中列出的接近用戶需用要的那一組流量(m³/h)及壓力值（Mpa）； η、η₀為在性能表標定的流量、壓力時對應的總效率及容積效率。它們可在相應的η-P曲線圖中查得。曲線均有離散性，按照"隨規格的增大而取大值" 的原則進行取值。	1.When the pressure is from P to P1,but viscosity and speed do not change,you count the power N: N =(QP₁/3.67η₀)[1+(η₀/η-1)P/P₁] (Kw) Note: The Q, P is the data that you can get from characteristic table Q(m³/h) and P(Mpa). η,η₀is the corresponding total efficiency and volume efficiency when the capacity and pressure is signed by Q, P. You can get them from η-P Drawing.
2. 當粘度從 E 變成 E₁而壓力、轉速不變時， N = (QP/3.67η₀)[1+(η₀/η-1)√E₁/E] (Kw)	2. When the viscosity is from E to E₁, but the pressure and speed don"t change, you can count the power: N = (QP/3.67η₀)[1+(η₀/η-1)√E₁/E] (Kw)
3. 轉速從 n 變成 n₁時，壓力、粘度不變時，軸功率 N： N = (Qpn/3.67η₀n₁)[1+(η₀/η-1)√n₁/n] (Kw)	3. When the speed is from n to n1, but the pressure and viscosity don"t change, you can count the power N: N = (Qpn/3.67η₀n₁)[1+(η₀/η-1)√n₁/n] (Kw)
(二) 流量的換算	(二)　The count of capacity
1. 對于粘度大于50E 的介質，當粘度從E變成 E₁時，流量 Q 變?yōu)?Q₁： Q₁= Q/η₀[1-(1-η₀)1/K] (m³/h) K=(√E₁+1.5)/(√E+1.5) 注：η₀為標定流量Q時的容積效率； E、E₁單位恩氏粘度⁰E 。	1. When the Viscosity is from E1 and they are more than 50E, the capacity will be form Q to Q1: Q₁= Q/η₀[1-(1-η₀)1/K] (m³/h) K=(√E₁+1.5)/(√E+1.5)
2. 當轉速從n變成n₁而粘度、壓力不變時，流量Q₁近似為： Q₁= Q/η₀[n₁/n-(1-η₀)] (m³/h)	2.When the speed is from n to n₁, but the viscosity and pressure don"t change, the capacity Q₁can count approximately: Q₁= Q/η₀[n₁/n-(1-η₀)] (m³/h)